dc.contributor.author |
Штегін, О.О. |
|
dc.contributor.author |
Юмашев, В.Є. |
|
dc.contributor.author |
Shtehin, O.O. |
|
dc.contributor.author |
Yumashev, V.E. |
|
dc.date.accessioned |
2016-03-16T13:48:02Z |
|
dc.date.available |
2016-03-16T13:48:02Z |
|
dc.date.issued |
2015 |
|
dc.identifier.uri |
http://eztuir.ztu.edu.ua/123456789/2035 |
|
dc.description.abstract |
Досліджено вплив кута нахилу поверхні, що обробляється, на динамічну сталість процесу різання. Проведено низку досліджень щодо обробки сферичною кінцевою фрезою поверхонь з різним кутом нахилу (від 7,5 до 52,5° з кроком 7,5°) для попутного фрезерування за висхідною та низхідною стратегіями. Результати цих експериментів показали, що фрезерування за висхідною є більш сталим при всіх значеннях кута нахилу. Це викликано меншими значеннями ефективних радіусів різального інструменту і, як наслідок, меншими значеннями швидкості різання і більшими значеннями сили різання. Під час обробки з малими кутами нахилу (до 15°) мали місце вібрації з частотою проходження зуба. Особливо це явище проявлялося при фрезеруванні за низхідною стратегією. Також було показано, що амплітуда коливань практично не збільшується при значному (в 5 разів) збільшенні радіальної глибини різання. Більше того, в деяких випадках (малий кут нахилу, низхідна стратегія) амплітуда навіть стає меншою. |
uk_UA |
dc.language.iso |
uk |
uk_UA |
dc.publisher |
ЖДТУ |
uk_UA |
dc.relation.ispartofseries |
Вісник ЖДТУ. Серія: Технічні науки;1(72) |
|
dc.subject |
вібрації при різанн |
uk_UA |
dc.subject |
сферичні кінцеві фрези |
uk_UA |
dc.subject |
динамічна сталість |
uk_UA |
dc.subject |
верстати з ЧПК |
uk_UA |
dc.subject |
cutting vibrations |
uk_UA |
dc.subject |
chatter |
uk_UA |
dc.subject |
ball end mills |
uk_UA |
dc.subject |
stability diagram theory |
uk_UA |
dc.subject |
CNC machines |
uk_UA |
dc.title |
ДОСЛІДЖЕННЯ ДИНАМІЧНОЇ СТАЛОСТІ ПРОЦЕСУ РІЗАННЯ НАХИЛЕНИХ ПОВЕРХОНЬ СФЕРИЧНИМИ КІНЦЕВИМИ ФРЕЗАМИ |
uk_UA |
dc.title.alternative |
Investigation of the dynamic stability of cutting process of inclined surfaces with ball end mills |
uk_UA |
dc.type |
Article |
uk_UA |
dc.description.abstracten |
The effect of the inclination angle of machining surface on the dynamic stability of cutting process is investigated. A number of machining tests of the surfaces with different inclination angles (from 7,5 up to 52,5 degrees with step of 7,5 degrees) were carried out for upward and downward climb milling with ball end mill. Results of these tests showed that upward climb milling is more stable for all values of inclination angle. It caused by smaller values of effective radii of cutting tool and, as a result, smaller values of cutting velocity and larger values of cutting forces. During the cutting with small values of inclination angle (up to 15 degrees) vibrations with tooth pass frequency took place. Especially this phenomenon was present in downward milling. Also it had been shown that oscillation magnitude almost does not increase when radial depth of cut increases significantly (5 times more). Furthermore, in some cases (small inclination angle, downward) magnitude even becomes smaller. |
uk_UA |