dc.contributor.author |
Радкевич, С.І. |
|
dc.contributor.author |
Глембоцька, Л.Є. |
|
dc.contributor.author |
Мельничук, П.П. |
|
dc.contributor.author |
Radkevych, S.I. |
|
dc.contributor.author |
Hlembotska, L.Ye. |
|
dc.contributor.author |
Melnychuk, P.P. |
|
dc.date.accessioned |
2023-07-11T11:59:26Z |
|
dc.date.available |
2023-07-11T11:59:26Z |
|
dc.date.issued |
2023 |
|
dc.identifier.uri |
http://eztuir.ztu.edu.ua/123456789/8194 |
|
dc.description.abstract |
У статті на підставі аналізу літературних джерел викладено існуючі уявлення про структурні особливості високоміцних чавунів з вермикулярним графітом (ЧВГ), при порівнінні його з сірими чавунами (СЧ) та високоміцними чавунами з кулястим графітом. Розглянуто вплив хімічного складу і структури на їх оброблюваність різанням, експлуатаційні властивості і стан поверхневого шару заготовки та можливості його покращення. Було виявлено, що інструменти з надтвердих матеріалів на основі кубічного нітриду бору (КНБ) та інструменти з металокераміки не забезпечуюють такої високої ефективності при обробці чавунів з вермикулярним графітом, як при обробці сірих чавунів. Найкращі показники оброблюваності в парі ЧВГ – КНБ були досягнені при переривчастому фрезуруванні зі швидкістю 800 м/хв. Відсутність MnS у складі ЧВГ та вермикулярна форма гафітових включень є основними чиниками, які ускладнюють їх обробку. До того ж вермикулярна морфологія чавунів сприяє швидкому дифузійному зносу інструментів з надтвердих матеріалів. Тут представлено результати стійкості інструментів з надтвердих і твердосплавних матеріалів при обробці торцевими фрезами поверхонь деталей з чавунів з вермикулярним графітом та з сірих чавунів. А також характер зношування, який при цьому наявний. |
uk_UA |
dc.language.iso |
uk |
uk_UA |
dc.publisher |
Державний університет "Житомирська політехніка" |
uk_UA |
dc.relation.ispartofseries |
Технічна інженерія;1(91) |
|
dc.subject |
чавун з вермикулярним графітом |
uk_UA |
dc.subject |
структура |
uk_UA |
dc.subject |
хімічний склад |
uk_UA |
dc.subject |
оброблюваність |
uk_UA |
dc.subject |
стійкість |
uk_UA |
dc.subject |
cast iron with vermicular graphite |
uk_UA |
dc.subject |
structure |
uk_UA |
dc.subject |
chemical composition |
uk_UA |
dc.subject |
machinability |
uk_UA |
dc.subject |
resistance |
uk_UA |
dc.title |
Підвищення ефективності обробки високоміцних чавунів з вермикулярним графітом |
uk_UA |
dc.title.alternative |
Improving the processing efficiency of high-strength cast irons with vermicular graphite |
uk_UA |
dc.type |
Article |
uk_UA |
dc.description.abstracten |
The article, based on the analysis of literature sources, describes the existing ideas about the structural features of high-strength cast irons with vermicular graphite (CGI), when compared with gray cast irons (GCI) and high-strength cast irons with spheroidal graphite. The influence of chemical composition and structure on their machinability, as well as the operational properties and condition of the surface layer of the workpiece, and the possibilities of its improvement, are considered. It has been found that tools made of superhard materials based on cubic boron nitride (CBN) and cermets do not provide such high efficiency when machining cast irons with vermicular graphite as when machining gray cast irons. The best machinability in the CGI-CBN pair was achieved with intermittent milling at a speed of 800 m/min. The absence of MnS in the composition of the CBN and the vermicular shape of graphite inclusions are the main factors that complicate their processing. In addition, the vermicular morphology of cast irons contributes to the rapid diffusion wear of tools made of superhard materials. This paper presents the results of the durability of tools made of superhard and carbide materials when machining the surfaces of parts made of vermicular graphite cast iron (CGI) and gray cast iron (GC) with end mills. Also, the nature of wear, which is present in this case. |
uk_UA |